View LPR2430ER_8583572.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

www.rfm.com e-mail: info@rfm.com page1of6 ?2009 by rf monolithics, inc. LPR2430ER - 06/19/09 LPR2430ER rating value units all input/output pins -0.3 to +3.6 v non-operating ambient temperature range -40 to +85 o c LPR2430ER absolute maximum ratings LPR2430ER electrical characteristics characteristic sym notes minimum typical maximum units operating frequency range 2405 2475 mhz operating frequency tolerance -300 300 khz spread spectrum method direct sequence modulation type o-qpsk number of rf channels 15 rf data transmission rate 250 kb/s symbol rate tolerance 120 ppm rf channel spacing 5 mhz receiver sensitivity, 10e-5 ber -95 dbm upper adjacent channel rejection, +5 mhz 41 db lower adjacent channel rejection, -5 mhz 30 db upper alternate channel rejection, +10 mhz 55 db lower alternate channel rejection, -10 mhz 53 db maximum rf transmit power 18 dbm transmit power adjustment 20 db optimum antenna impedance 50 ? 2.4 ghz spread spectrum transceiver module small size, light weight, +18 dbm transmitter power sleep current less than 3 a fcc, canadian ic and etsi certified for unlicensed operation high power 802.15.4 module the LPR2430ER 2.4 ghz transceiver module is a low cost, high-power solution for peer-to-peer, point-to-point and point-to-multipoint wireless designs. LPR2430ER modules provide the flexibility and versatility to serve applications ranging from cable replacements to sensor networks. based on the ieee 802.15.4 wireless standard, the LPR2430ER module is easy to integrate and provides robust wireless communi - cations in applications where full mesh network operation is not required. the LPR2430ER includes cnl v2.0 network layer firmware which features a flexible and simple-to-use application programming interface. shown with shield removed development kit (info click here )
www.rfm.com e-mail: info@rfm.com page2of6 ?2009 by rf monolithics, inc. LPR2430ER - 06/19/09 characteristic sym notes minimum typical maximum units adc input range 0 3.3 v adc input resolution 11 bits adc input impedance 55 m pwm output resolution* 8 16 bits uart baud rate 1.2, 2.4, 4.8, 9.6 (default), 19.2, 28.8, 38.4, 57.6, 76.8, 115.2 kb/s digital i/o: logic low input level -0.3 0.5 v logic high input level 2.8 3.3 v logic input internal pull-up resistor 20 k gpio3 logic low sink current 20 ma power supply voltage range v cc +3.3 +5.5 vdc power supply voltage ripple 10 mv p-p receive mode current 33 ma transmit mode current 130 ma sleep mode current 3a operating temperature range -40 85 o c *pwm0 has 8-bit resolution, pwm1 has 16-bit resolution. built-in pwm output filters suppress ripple to 7 bits. additional filtering can be added externally. LPR2430ER electrical characteristics caution: electrostatic sensitive device. observe precautions when handling.
www.rfm.com e-mail: info@rfm.com page3of6 ?2009 by rf monolithics, inc. LPR2430ER - 06/19/09 LPR2430ER hardware the major hardware component of the LPR2430ER is the cc2430 ieee 802.15.4 compatible transceiver with integrated 8051 microcontroller. the LPR2430ER operates in the frequency band of 2405 to 2475 mhz at a nominal output power of 63 mw. the LPR2430ER includes a low noise preamplifier in the receiver path and a power amplifier in the transmit - ter path, greatly increasing the operating range of the cc2430. two crystals are provided to operate the cc2430, a 32 mhz crystal for normal operation and a 32.768 khz crystal for precision sleep mode operation. the LPR2430ER provides a variety of application hardware interfaces including a uart interface, three 11-bit adc inputs, two pwm (dac) outputs, and six general purpose digital i/o ports. LPR2430ER firmware the main firmware components in the LPR2430ER in- clude the 802.15.4 media access control (mac) layer and the cnl v2.0 networking layer. cnl v2.0 sup - ports up to 63 remotes. network topologies include point-to-point, point-to-multipoint and peer-to-peer. cnl employs one-hop relay forwarding to mitigate network transmission problems such as multipath fad - ing. cnl includes provisions for low-power sleep mode operation with periodic wakeup and report. the cnl application programming interface (api) pro - vides an easy-to-use, flexible set of application com - mands and functions. the api includes support for send/receive serial data, read/write gpio, read adc inputs, write pwm outputs and module configuration services. in addition, cnl supports analog and digital i/o binding, which maps an adc measurement and the states of two digital inputs on one LPR2430ER to a pwm output and two digital outputs on another LPR2430ER. see the lpr2430 series integration guide for complete details of the cnl api.

! ! " ! " ! # $ % & ' ( ' & ) ' $ * # ' + , % - " . % ' + - & / % ' + - / 0 1 + 2 & - & 2 , # ' + . 0 1 + 2 & - & 2 , # ' +
. 3 # ' + , 3 . # ' + # ' + , 2
- $ . 3 , # ' + . ( # $ 4 ( " ' + 1 5 1 5 # $ 0 2 & % 2 ( 2 ( 2 ( 2 ( % % - ( $ $ 2 6 7 & 0 & 0 3 " ! % 4 ( & / 0 / 8 ! figure 1
pin name i/o description 1 gnd - power supply and signal ground. connect to the host circuit board ground. 2 activity o rf activity indicator. output pulses high when a packet is sent or received. 3 link o link indicator. output is high when the radio has successfully joined a network. 4 gpio0 (adc_ref) i/o configurable digital i/o port 0. when configured as an output, the power-on state is also configurable. this pin can also be configured as a reference voltage input for the adcs, 0 to 3.3 v, 1.25 v typical. 5 radio_txd o serial data output (uart) from the radio to the host. 6 radio_rxd i serial data input (uart) from the host to the radio. 7 gpio4 (/host_cts ) i/o configurable digital i/o port 4. when configured as an output, the power-on state is also configurable. also configurable as uart flow control output. the lpr2430 sets this line low to indicate it is ready to accept data from the host on the radio_rxd input. when the lpr2430 sets this line high, the host must stop sending data. the default state is gpio4. 8 gpio5 (/host_rts) i/o configurable digital i/o port 5. when configured as an output, the power-on state is also configurable. also configurable as uart flow control input. the host sets this line low to allow data to flow from the radio_txd pin. when the host sets this line high, the lpr2430 will stop sending data to the host. the default state is gpio5. 9 pwm0 o pulse-width modulated output 0 with internal low-pass filter. provides a dac function, 0 to 3.3 v. 10 gpio2 (pwm1) i/o configurable digital i/o port 2. when configured as an output, the power-on state is also configurable. this pin is con - nected to the input of the low-pass filter driving pin 13, and is also configurable as a pwm output. 11 gpio1 i/o configurable digital i/o port 1. when configured as an output, the power-on state is also configurable. 12 gpio3 (rs485_en) i/o configurable digital i/o port 3. when configured as an output, this high current port can sink up to 20 ma. the power-on output state is also configurable. can also be configured as active low transmit enable for controlling an rs485 or other half-duplex bus driver. 13 pwm1 (gpio2) o gpio2 (pin 10) drives this pin through a low-pass filter. provides a dac function when gpio2 is configured as a pwm output. 14 vcc i power supply input, +3.3 to +5.5 vdc. 15 gnd - power supply and signal grounds. connect to the host circuit board ground. 16 gnd - power supply and signal grounds. connect to the host circuit board ground. 17 /reset i active low module hardware reset. hold this input low when the power supply input is less than 3.3 vdc. the module firm - ware boots up and will accept commands about 3 seconds after this input goes high. 18 adc0 i 11-bit adc input 0. adc full scale reading can be referenced to the module?s +3.3 v regulated supply, the adc?s internal +2.5 v reference, or adc_ref (pin 4). 19 adc1 i adc input 1. same configuration options as adc0. 20 rsvd - reserved pin. leave unconnected. 21 rsvd - reserved pin. leave unconnected. 22 rsvd - reserved pin. leave unconnected. 23 rsvd - reserved pin. leave unconnected. 24 adc2 i adc input 2. same configuration options as adc0. 25 adc_vdd o module?s +3.3 v regulated supply, used for ratiometric adc readings. current drain should be less than 5 ma. 26 nc - no connection. 27 nc - no connection. 28 gnd - rf ground. connect to the host circuit board ground plane, and to shield when using coaxial cable. 29 rfio i/o rf port. connect the antenna to this port with a 50 stripline or semi-rigid coaxial cable. 30 gnd - rf ground. connect to the host circuit board ground plane, and to shield when using coaxial cable. www.rfm.com e-mail: info@rfm.com page4of6 ?2009 by rf monolithics, inc. LPR2430ER - 06/19/09 LPR2430ER i/o pad descriptions
rfio stripline the rfio pad on the radio module is connected directly to an antenna on the host circuit board, or to an mmcx or similar rf connector. it is important that this connection be implemented as a 50 ohm stripline. referring to figure 3, the width of this stripline depends on the thickness of the circuit board between the stripline and the groundplane. for fr-4 type circuit board materials (dielectric constant of 4.7), the width of the stripline is equal to 1.75 times the thickness of the circuit board. note that other circuit board traces should be spaced away from the stripline to prevent signal coupling, as shown in figure 4. the stripline trace should be kept short to minimize its insertion loss. www.rfm.com e-mail: info@rfm.com page5of6 ?2009 by rf monolithics, inc. LPR2430ER - 06/19/09
+ 9 ! 9 ! : :
& ; ( ! 6
! : : 7 ! : figure 2 ; ; ! # 9 ! ; ; ! 2 ; ! & ! " < ! 9 2 ; ! & ! ! "
7 ; ! ! 3 =
> 1 figure 3 figure 4 trace separation from 50 ohm microstrip length of trace run parallel to microstrip 100 mil 125 mil 150 mil 200 mil 200 mil 290 mil 250 mil 450 mil 300 mil 650 mil
reflow profile an example solder reflow profile for mounting the radio module on its host circuit board is shown in figure 5. www.rfm.com e-mail: info@rfm.com page6of6 ?2009 by rf monolithics, inc. LPR2430ER - 06/19/09 figure 5 note: specifications subject to change without notice. part # m-2430-0004, rev a

▲Up To Search▲

Price & Availability of LPR2430ER

	To Download LPR2430ER Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .